Introduction
Dogs are great companions and bring joy to our lives, but sometimes their fur can become an issue. If your dog spends a lot of time with you, chances are their fur will end up in your washer. It’s important to know how to get the dog hair out of your washer to ensure it’s clean and running properly.
This article will provide 8 easy steps on how to get dog hair out of your washer. From using a lint roller or sticky tape to pre-treating stains with pet hair removal detergent and running a cycle with baking soda and hot water, keep your washer clean and free from pet hair.
Using a Lint Roller or Sticky Tape
The first step in getting rid of dog hair from your washer is to use a lint roller or sticky tape. This method is quick and simple, but only works if there is a small amount of fur in the washer.
Steps for Using a Lint Roller
1. Open the washer door and take out any clothing that may be inside.
2. Roll the lint roller over the inside walls of the washer.
3. Continue rolling until all visible fur has been removed.
4. Close the washer door and check for any remaining fur.
Benefits of Using Sticky Tape
Sticky tape is also effective at removing dog hair from your washer. The advantage of using sticky tape is that it doesn’t leave behind any residue like lint rollers can. Here are the steps for using sticky tape:
1. Open the washer door and take out any clothing that may be inside.
2. Cut a piece of sticky tape and attach it to the wall of the washer.
3. Gently press down and pull up the sticky tape.
4. Repeat this process until all visible fur has been removed.
5. Close the washer door and check for any remaining fur.
Vacuuming the Interior of the Washer
If there is more than just a few strands of dog hair in your washer, vacuuming the interior might be the best option. This method will remove any loose fur, as well as any fur that is stuck in hard to reach places.
What Type of Vacuum Should Be Used?
It is recommended to use a handheld vacuum cleaner when vacuuming the interior of the washer. This type of vacuum will make it easier to reach all the nooks and crannies of the washer. Make sure the vacuum is powerful enough to remove all the fur.
Where to Focus the Vacuum
When vacuuming the inside of the washer, focus on the edges and corners where fur tends to accumulate. Also, pay special attention to the seals around the door, as this is where a lot of fur can hide. After vacuuming, check the drum for any remaining fur.
Wiping Down the Inside with a Damp Cloth
Once the loose fur has been removed, it’s time to wipe down the interior of the washer with a damp cloth. This will help to remove any remaining fur as well as any dust and dirt that may have accumulated.
Suggested Cleaning Solutions
Before wiping down the inside of the washer, mix a solution of warm water and mild detergent. Use a soft cloth or sponge to wipe down the walls of the washer. For stubborn stains, try using a mixture of baking soda and water.
Areas to Focus on When Cleaning
When cleaning the inside of the washer, focus on the areas where fur tends to accumulate. Pay special attention to the seals around the door, as this is where a lot of fur can hide. Also, make sure to wipe down the drum to remove any remaining fur.
Running a Cycle with Hot Water and White Vinegar
After wiping down the inside of the washer, it’s time to run a cycle with hot water and white vinegar. This will help to remove any remaining fur as well as any odors that may be lingering in the washer.
Amount of White Vinegar Needed
For best results, use one cup of white vinegar for every load of laundry. Pour the white vinegar into the washer before adding the clothes. Make sure to use hot water for the cycle so that the vinegar can effectively remove the fur.
Benefits of This Method
Running a cycle with white vinegar and hot water helps to dissolve any remaining fur in the washer. It also helps to remove any odors that may be present. In addition, it helps to prevent the build-up of lint and fur in the washer.
Removing Hair from the Drum with a Rubber Spatula or Brush
If there is still fur left in the washer after running a cycle with hot water and white vinegar, it’s time to remove it manually. This can be done by using a rubber spatula or brush to scrape off the fur.
Recommended Tools
A rubber spatula or brush is the best tool for removing fur from the drum of the washer. Make sure to use a gentle motion when scraping off the fur to avoid damaging the drum.
Steps for Hair Removal
1. Open the washer door and take out any clothing that may be inside.
2. Use a rubber spatula or brush to scrape off any remaining fur from the drum.
3. Continue scraping until all visible fur has been removed.
4. Close the washer door and check for any remaining fur.
Pre-Treating Stains with Pet Hair Removal Detergent
If there are any stubborn stains caused by pet hair, pre-treating them with a pet hair removal detergent can help to remove them. This type of detergent is specially formulated to break down and remove pet hair.
Types of Detergents Available
There are many types of pet hair removal detergents available on the market. Choose one that is safe for use in washing machines and follow the instructions on the package for best results.
How to Apply Detergent
To pre-treat the stains, add the detergent to the washer before adding the laundry. Make sure to follow the instructions on the package for best results. After pre-treating the stains, run a cycle with hot water to remove any remaining fur.
Running a Cycle with Baking Soda and Hot Water
The last step in getting rid of dog hair from your washer is to run a cycle with baking soda and hot water. This will help to neutralize any odors that may be present in the washer.
Amount of Baking Soda Needed
For best results, use one cup of baking soda for every load of laundry. Pour the baking soda into the washer before adding the clothes. Make sure to use hot water for the cycle so that the baking soda can effectively remove odors.
Benefits of This Method
Running a cycle with baking soda and hot water helps to neutralize any odors that may be present in the washer. It also helps to keep the washer smelling fresh and clean. In addition, it helps to prevent the build-up of lint and fur in the washer.
Conclusion
Getting dog hair out of your washer doesn’t have to be a daunting task. With the right tools and methods, you can easily remove any pet hair and keep your washer clean and running properly. From using a lint roller or sticky tape to pre-treating stains with pet hair removal detergent and running a cycle with baking soda and hot water, keep your washer free from pet hair.
